Abstract:In order to enhance aircraft engine heat transfer performance in the conditions of ground idle speed or low flying speed, a surface air-oil exchanger was presented using air inlet passage as its dissipation area. Its heat dissipation characteristics, as well as districted simulation equivalence, were investigated through the studies of 4 districted mode, 7 districted mode and the mode of using flat surface to replace arc surface. The numerical results demonstrate that temperature distributions in air side are almost the same in the cases of 4 districted mode, 7 districted mode and the mode used flat surface to replace arc surface in the simulations. All of their temperature differences are smaller than 1 K, and the discrepancies of calculated heat dissipation power are below 5%. The phenomena of heat transfer in oil side are also the same in the three cases. The research validates the feasibility and reliability of the methods of using districted simulation and using flat surface instead of arc surface where the ratio of arc length to diameter is below 0.203, when analyzing thermal characteristics of a large surface heat exchanger.
HUANG H, SPADACCINI L J, SOBEL D R. Fuel-cooled thermal management for advanced aeroengines[J]. Journal of Engineering for Gas Turbines and Power, 2004, 126: 284-293
[2]
寿荣中,何慧姗. 飞行器环境控制[M]. 北京:北京航空航天大学出版社,2004:35-38.
[3]
朱春玲,宁献文. 用于机载大功率电子设备的新型液冷环控系统的研究[J]. 南京航空航天大学学报,2005,37(2): 203-207ZHU Chunling, NING Xianwen. Liquid cooling system for high-powered avionics[J]. Journal of Nanjing University of Aeronautics & Astronautics, 2005, 37(2): 203-207
[4]
陈德雄,李敏. 飞机座舱制冷附件[M]. 北京:国防工业出版社,1981:22-24.
[5]
丁顺利. 飞机环形散热器的性能研究[D]. 南京:南京航空航天大学,2012.
[6]
帕坦卡. 传热与流体流动的数值计算[M]. 张郑译. 北京:科学出版社,1984:1-5.
[7]
陶文铨. 数值传热学[M]. 西安:西安交通大学出版社,1995:1-10.
[8]
WU H H, HSIAO Y Y, HUANG H S, et al. A practical plate-fin heat sink model[J]. Applied Thermal Engineering, 2011, 31(5): 984-992
[9]
PATANKAR S V,SPALDING D B. A calculation procedure for transient and steady state behavior of shell and tube heat exchanger[M]. Washington D. C.:Scripta Book Company,1974:77-79.
[10]
LI H Y, CHAO S M. Measurement of performance of plate-fin heat sinks with cross flow cooling[J]. International Journal of Heat & Mass Transfer, 2009, 52(13/14): 2949-2955
[11]
蔡惠坤,张银亮,廖亦戴,等. 多海拔下不同散热器翅片的性能分析[J]. 华南理工大学学报(自然科学版),2017,45(2): 91-98CAI Huikun, ZHANG Yinliang, LIAO Yidai, et al. Performance analysis of different radiator fins at various altitudes[J]. Journal of South China University of Technology (Natural Science Edition), 2017, 45(2): 91-98
[12]
LI H Y, CHAO S M, CHEN J W, et al. Thermal performance of plate-fin heat sinks with piezoelectric cooling fan[J]. International Journal of Heat & Mass Transfer, 2013, 57(2): 722-732
[13]
李学康. 串联通道水冷散热器的建模与优化[D]. 成都:电子科技大学,2013.
[14]
YUAN W, ZHAO J, TSO CP, et al. Numerical simulation of the thermal hydraulic performance of a plate pin fin heat sink[J]. Applied Thermal Engineering, 2012, 48: 81-88
[15]
CHEN C T, CHEN H I. Multi-objective optimization design of plate-fin heat sinks using a direction-based genetic algorithm[J]. Journal of the Taiwan Institute of Chemical Engineers, 2013, 44: 257-265
[16]
FENG S S, KUANG J J, WEN T, et al. An experimental and numerical study of finned metal foam heat sinks under impinging air jet cooling[J]. International Journal of Heat & Mass Transfer, 2014, 77: 1063-1074
[17]
CHEN H T, TSENG H C, JHU S W. Numerical andexperimental study of mixed convection heat transferand fluid flow characteristics of plate-fin heat sinks[J]. International Journal of Heat & Mass Transfer, 2017, 111: 1050-1062